Schedule a Visit
Main Street in downtown Roswell, New Mexico, with traffic and US 285, 70 and 380 route signs

Photo: Phil Campbell, CC BY 2.0 (cropped)

Commercial Spray Foam Insulation in Roswell

A commercial insulation contractor for Roswell warehouses, shops, offices, retail, and new pre-engineered metal buildings. Closed-cell and open-cell spray foam, sprayed on a schedule that works around your business.

Schedule a Visit

Commercial Spray Foam in Roswell

Spray foam for Roswell’s steel buildings, shops, and storefronts

Look at what goes up around the edges of Roswell and a lot of it is steel: pre-engineered buildings for shops, storage, farm supply, and retail, plus the offices and work buildings that keep the area’s dairies running. Out at the old Walker Air Force Base, now used for industry and aviation, big hangars and industrial buildings sit on open ground with nothing to slow the wind. Steel moves heat fast. On a July afternoon the roof panels throw heat straight down onto the floor, and on a clear January night the heat you paid for leaves through the same thin skin. The fiberglass blanket most metal buildings come with gets squashed at every purlin, sags, and does little about air leaking in at the eaves.

Closed-cell spray foam goes right onto the inside of the panels and seals the seams, fasteners, and eaves in the same pass. It bonds to the steel, so it doesn’t sag. For commercial new construction in Roswell, the building gets foamed once it’s dried in and before liner panels or interior walls go up. On an older building we check the roof first: hail-dented panels and leaking fasteners get fixed before any foam goes on, because foam hides a leak rather than stopping it.

Typical commercial insulation jobs in Roswell

  • New pre-engineered steel buildings foamed after dry-in, before interior finish
  • Farm-supply stores and dairy shops lined with sagging blanket insulation
  • Older downtown storefronts and offices with little above the ceiling
  • Motels and restaurants along the highways that run through town
  • Warehouses and storage buildings where wind and dust get in at the eaves

What we plan around in Roswell

  • Hot summer sun on bare steel roofs, radiating down onto the floor
  • Spring wind and dust pushing in at eaves, panel laps, and doors
  • Monsoon hail and hard rain, so roof leaks get fixed before any foam
  • Clear January nights that draw heat out through thin steel walls

How it works

  1. Step 1

    Site visit

    We look at the building, how it is used, and when the work can happen without getting in your way.

  2. Step 2

    Schedule and prep

    Work is set around your hours, often a section at a time, with equipment, stock, and fixtures masked.

  3. Step 3

    Spray

    Foam goes on to the specified thickness. Any thermal or ignition barrier coating the building’s use requires is part of the estimate.

  4. Step 4

    Walk-through

    We check coverage and thickness against the estimate and walk the finished job with you.

Also serving: Midway, Dexter, Hagerman, Lake Arthur.

Guides

Worth reading before you call

All guides

Spray foam roofing guide

Is your roof a candidate for spray foam?

A foam roof can go over many flat and low-slope roofs, as long as what’s under it is dry, sound and draining. Here’s how to tell whether yours is a candidate and how to look after it.

5 min read

Concrete lifting guide

Sidewalk trip hazards: lift, grind or replace

An offset between two sidewalk panels is a small thing until someone catches a toe on it. Here is how those lips form, why they matter more on a commercial property, and how to choose between lifting, grinding and replacing.

5 min read

Commercial Spray Foam in Roswell: common questions

Usually closed-cell. It bonds to the steel, seals the seams and fasteners, gives the most R-value in a thin layer, and blocks moisture, which matters when warm inside air meets panels chilled by a winter night. Open-cell can make sense for a framed office or finished room inside the building, where it fills the cavities for less. How the building is used decides it.
Once the building is dried in, with roof and wall panels on and doors set, and before liner panels, interior walls, or ceilings go up. That is when every panel and purlin can be reached. Electrical and plumbing along the walls should be roughed in first. Bring us in while the building is still going up, so the foam fits your builder’s schedule instead of holding it up.
Yes. Our commercial insulation services cover Roswell and the farm country around it, including Midway, Dexter, Hagerman, and Lake Arthur. That means shops, offices, farm-supply stores, and storage buildings. It helps to know whether the steel is bare or already has blanket insulation behind it.

Need commercial insulation in Roswell?

Tell us what the building is used for, how big it is, and whether it’s new or existing, and we’ll set up a site visit.

Schedule a VisitSend PlansCall (855) 575-3626